«

»

Oct
31

Plumbing Made Simple – Tips To Help You On Your Plumbing Projects

Plumbing Made Simple - Tips To Help You On Your Plumbing Projects

Plumbing Made Simple – Tips To Help You On Your Plumbing Projects

Plumbing can really get you in a bad situation. It is your responsibility to make sure that you know at least the basics to ensure that you do not lose valuable property and end up costing yourself much more money. Use this article for the best plumbing advice.

Rigid copper is used for main water lines in many homes. You cannot bend rigid copper, so joints and tees must be soldered on. When soldering, always apply flux (also called soldering paste) to both surfaces. Flux retards oxidation when the copper is heated. Always use lead-free or nearly lead-free solder when sweating a copper joint.

Make sure you know where your home’s water shutoff is located. You never know when there might be an emergency involving a broken pipe or damaged connection that requires you to turn off the water right away. In addition, knowing where the shutoff is located is vital before you start any plumbing project, in case anything goes wrong.

If you have noisy pipes, you can cushion them with a rubber blanket or add additional anchor straps. Banging pipes are usually caused by loose pipes, water hammering to a stop as you turn it off, or hot water pipes shifting in their position. All of these problems can be solved by cushioning and anchoring the pipes.

Do not forget to check the temperature of the water heater in your house, especially if you are planning to leave for an extended period of time. You should keep the temperature no higher than 120 degrees, which will help to reduce energy use and prevent your system from burning out.

Keep an eye on the hoses for your dishwasher and washing machine. These hoses can leak and bulge, which can be a problem. Check them for signs of wear and tear and replace any hoses more than 10 years old. You’ll find that these hoses age well, but you have got to make sure they are doing the job they should.

Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there’s a place to recycle it near your home.

Many people wonder where the fruit flies are coming from. Each plumbing fixture has a self-sealed reserve that holds about two cups of water. If those pipes are broken or do not seal off, then odors and residue can cause fruit flies. It is recommended before anything to clean your pipes using bleach. If the flies come back, contact a professional.

Try to avoid the use of dry cleaners as often as you can. The chemicals in these type of cleaners are corrosive, and they could damage your pipes by using them too much. If you find that your drain is clogged, think about hiring a plumber to do a estimate and tell you what the issue is.

The clean out plug can sometimes be difficult to remove, and if you are having problems, there are two approaches to fixing this problem First, the clean-out fitting can be loosened with a hammer and chisel. The only other thing you can do is chisel through it.

Make sure that any exposed pipes in your home are insulated, especially those found in crawl spaces on the outside walls of your home. This will help keep them from freezing and causing you tons of problems. Frozen pipes can often be devastating and leave you with problems that are expensive to fix and no water in the middle of winter.

Ask before the plumber comes out if they charge for the consultation. In order to quote a project, the plumber has to come out to inspect your particular issue. It is standard to charge for the consultation appointment but the prices can vary wildly. Ask upfront so that you aren’t surprised by the total.

To prevent pipe banging when you turn on the water, think about rubber blankets or straps. Instead of assuming the pipes need replaced, consider anchoring them or buffering them. If your pipes are plastic, leave them some room for expansion and contraction. If pipes do not leak but just make noise, eliminate the noise.

Make sure that the temperature of your home’s water heater is not above 120F. On older water heaters, be sure it is not above medium settings. When temperatures get higher than 120, scalding can occur. Also, having the settings above 120F, tends to use more energy than lower temperatures do.

In conclusion, you want to back yourself up as much as you can when it comes to taking care of plumbing issues. Use the details in this article to make sure that you know all of the ins and outs so that you can hopefully avoid having somebody else come out to take care of your issues.

Leave a Reply

Your email address will not be published.

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>